10" colour touchscreen: 1805 & 1886 series
Modern digital technology for safety-current-limited applications or those at 500 VA / 200 mA.
Testing system for stators
Two test stations were required in order to test the stators before and after the impregnating. Two almost identical test stations were setup for this purpose in order to be able to use both stations for both types of tests during peak times. A high level of flexibility was required due to the high diversity of the DUT.
Test system for safety magnets
Locking solenoids must be checked for functionality and safety before deployment in industrial robots.
Safety test system for solar inverters
Fully automatic safety test system for solar inverters with function test, running in station and customizing system.
Safety test system for solar inverters
EOL safety test system for solar inverters with fully automatic contacting before endurance tests.
Test system for Pedelec motors
EOL Pedelec motor function test system for E-bikes with complete programming. Among others, there are speedometer, rear and main lights simulated on the motors.
Test system for electrical brakes and connector sockets
Electrical brakes and connector sockets are essential components for automation technology. Particularly high requirements are made in the medical field on surgical robots.
Testing systems for 1-, 2- and 3-phase stators
Following the production of electric motors in the medium power range, the stators are tested for safety and function. A wide range of products, low quantities and highest quality characterize this production. The Product Liability Act requires permanent storage of all test data.
Testing systems for motors 3 x 400 V / 63 A / 50 Hz
Complete testing of electric motors at the end of line. A safety and function test is necessary at the end of line for the 3-phase motors following production.
Test system for PX-LED spotlights
Especially with explosion-proof products an intensive quality assurance is absolutely necessary. Therefore the explosion-proof luminaires have to be submitted to a safety and function test. For a new product of our customer a fully automatic test system was to be developed to be integrated directly into the production line.
LED light testing system L1800
Modern LED lights, too, must be tested for electrical safety and function after production. Because of the completely new technology respective new test techniques are necessary.
Stator testing system S 1800
Stators of electric motors must be subjected to an intensive test in production. Only then the stator with the rotor is assembled to an electric motor.
Testing system for surgical instruments
Upon completion of the production of surgical instruments, electrical continuity and integrity of the plastic wrap must be examined. For multi-pole instruments, the insulation between the two electrodes must also be checked.
Safety, function and leak test for electric submersible pumps
The submersible pumps manufactured must be tested as automatically as possible. In addition to the safety tests, function test of the pump and leak test of the motor compartment, including the float switch, were performed.
Final testing bench for brushless servomotors
Compact testing system for the final testing of fully assembled motors.
Safety, function and leak testing system for electric pumps
The pumps manufactured for domestic use must be tested as automatically as possible. In addition to the safety tests, function test of the pump and leak test of the pump chamber were performed.
Testing system for soldering stations
Modern soldering stations are complex devices with a lot of electronics. At the end of production, the quality must be ensured by a safety and function test.
Testing system for commercial kitchens up to 600 A
Complete electrical testing of large kitchens for commercial applications. A safety and function test is necessary for the most 3-phase DUT following production.
Testing systems for determining the energy efficiency rating of refrigerator / freezer combo units
The power consumption of household appliances is very important for the end user and therefore, an unique selling point. Comprehensive, standardized, long-term measurements are needed to determine the energy efficiency rating.
Testing system for explosion-proof linear fluorescent luminaries
Intensive quality assurance is indispensable especially for explosion-proof products. Therefore, the explosion-proof luminaires must undergo a safety and function test.
Test system for coffee machines
For several years fully-automatic coffee machines are found not any more only in the professional sector. Not only restaurants and coffee houses use coffee machines but often these machines can be found in private households. As a result the number of units has risen significantly.
Hipot in a water bath for position sensors of the protection classes I, II and III
Sensors produced must be tested for electrical safety. A wide range of products and the highest quality characterize this production.
Universal, mobile testing system for various industries
Mobile and flexible safety testing system with additional leakage current test and an integrated industrial PC.
Testing system for PDUs (power distribution units) with up to 24 outlets
Testing system for continuity, ground bond and hipot tests for several 19'' MPH PDUs.
Testing system for power strips with a maximum of 12 Schuko sockets
Power strips must be tested for safety and function following their production.
EOL (end of line) tester for BDU subassemblies
Testing system for determining the electrical properties of automotive components.
Testing system for devices for high frequency surgery and lithotripsy systems
Medical devices must be tested for safety and function following their production.